A M E R I C A N O L E A N . C O M
Q U A R R Y T I L E
QUARRY FLOOR TILE
FAWN GRAY Q06
(2) GRAY FLASH Q16 (2) CANYON RED Q01
(1) EMBER FLASH Q02 (2) ABRASIVE GRAIN Q SPECIAL SURFACES:
Abrasive grain particles added to Quarry Tile give improved slip resistance for many types of footwear, depending on maintenance conditions. 6 x 6 size available in all Quarry colors; 3-7/8 x 8 size available in Q01 and Q02 colors only.
(1) & (2) notations indicate price group, (1) being the least expensive. All or select items within this series meet the requirements for these qualifications. For more information, refer to p. 304.
INSTALLATION & PRICING
RECOMMENDED GROUT JOINT: SHADE VARIATION Floor: 1/4" - 3/8" RELATIVE PRICING: Low to High MEDIUM (V2) (Solid) HIGH (V3) (Flashed)
ASTM# FLOOR RESULT Water Absorption C373 3.0% Breaking Strength C648 > 350 lbs. Scratch Hardness MOHS 7.0 Chemical Resistance C650 Resistant Abrasion Resistance C1027 N/A
THICKNESS SQ. FT./ CARTON PIECES/ CARTON 6 x 6 Floor Tile 6" x 6" (15.20 cm x 15.20 cm) 1/2" 11.00 44 3-7/8 x 8 Floor Tile 3-7/8" x 8" (9.80 cm x 20.30 cm) 1/2" 10.76 50
NUMBER PIECES/ CARTON Floor Bullnose
6 x 6 x 1/2 Q-1665 44 Floor Bullnose Corner
6 x 6 x 1/2 QCR-L-1665 44 Floor Bullnose (8" side)
3-7/8 x 8 x 1/2 Q-1485 50 Floor Bullnose Corner
3-7/8 x 8 x 1/2 QCR-L-1485 20 Cove Base H 5 x 6 x 1/2 Q-3565 44 Cove Base Long Corner H
5 x 6 x 1/2 QCR-L3565 20 Cove Base Outcorner H 5 x 1 x 1/2 QC-3565 20 Cove Base Incorner H 5 x 1 x 1/2 QB-3565 25 Cove base trim is intended to coordinate with floor tile in the standard 90-degree installation position.
Also available in abrasive grain
Not available in Flash colors
Available in colors Q01 and Q02 only
Available by special order only (except Q01)
Q U A R R Y T I L E QUARRY FLOOR
TARGET DCOF WET SUITABLE Dry & Level - Interior Floor N/A Wet & Level - Interior Floor 0.42 Shower Floors (Residential or Light Commercial) 0.42 Exterior Floor Applications (including pool decking & other wet areas with minimal footwear) 0.60 * Ramps & Inclines 0.65 * Walls/Backsplashes N/A Countertops N/A Pool Linings N/A A DCOF value of 0.42 is the standard for tiles specified for level interior spaces expected to be walked upon when wet, as stated in ANSI A137.1-2012, Section 9.6. For more information about DCOF and the DCOF AcuTest, refer to p. 294. APPLICATION NOTES: Suitable for industrial installations requiring high compressive strength. Subject to Oils: Absorbs oils, grease and other liquids to keep floors slip-resistant, yet does not contaminate the surface. Proper cleaning methods easily remove any contaminants that do get absorbed into the tile. * Abrasive surface only
Since there are variations in all fired ceramic and natural products, tile and trim supplied for your particular installation may not match samples. Final confirmation should be made from actual tiles and trim prior to installation. Manufactured in accordance with ANSI A137.1 standards. For additional information refer to "Factors to Consider" on p. 293. Suitable for exterior applications in freezing and non-freezing climates, when proper installation methods are followed. We do not recommend light colored quarry tile in commercial kitchens unless properly sealed or a grout release is used. Periodic resealing of the tile may be necessary. Special care should be taken when grouting; a grout release is recommended to prevent finely powdered pigments from lodging in the pores of the tile surface. It is necessary to follow the proper procedures and recommendations from the grout and maintenance products' manufacturers. For information on Test Results & Classifications, see p. 294. For Installation Considerations, Care & Maintenance information, see pp. 295-297.
FLOORS WALLS COUNTERTOPS
F W CPrevious Page